Repair TipsLocal Guides

Why is my roof leaking around the chimney in Des Moines

A roof leaking around the chimney in Des Moines usually traces to the flashing where the chimney meets the roof, but not always.

Brick chimney with metal flashing where it meets an asphalt shingle roof in Des Moines

The short answer: it's almost always the flashing

A roof leaking around the chimney in Des Moines usually traces to the flashing: the metal that seals the joint where the chimney meets the roof. That joint moves, weathers, and carries water from two surfaces at once, and when the flashing fails, water enters at the chimney line and shows up on ceilings and walls nearby.

Not every chimney-area leak is flashing, though. The crown, the brickwork, and the mortar joints can admit water too, and that work belongs to a mason rather than a roofer. Sorting out which trade owns the leak is the first job of an assessment, and this guide explains how the line is drawn: flashing is the roofer's, crown and brick are the mason's.

Why chimney flashing fails in Des Moines

Chimney flashing fails for reasons the Des Moines climate accelerates. Freeze-thaw cycles expand and contract the joint between the chimney and the roof, working flashing loose and opening gaps in sealant. The chimney and the roof move independently as temperatures change, and the flashing bridges that movement with every cycle.

Age adds to the movement. Sealant dries and shrinks, fasteners loosen, and step flashing pieces shift out of alignment. Storm damage finishes what age started: wind lifts flashing edges, and hail dents the metal. Two layers of flashing protect the joint, step flashing woven with the shingles and counter-flashing set into the chimney mortar, and failure in either layer admits water at the same place.

How to tell a chimney leak from a roof leak

A chimney-area leak usually shows up as stains on the ceiling or wall near the chimney, dampness after wind-driven rain, or water appearing where the chimney passes through the attic. A roof-surface leak further from the chimney shows up away from the chimney line, though water can travel along framing and mislead the eye.

Attic observation helps: stains on the decking at the chimney line, dampness on the chimney-side rafters, and water paths running from the flashing area all point to the joint. The distinction matters because the repair differs, and a leak detection and repair assessment traces the path rather than guessing from the stain.

What decides the scope of a chimney leak repair

The scope of a chimney leak repair depends on which layer failed, how far the water traveled, and whether the masonry is involved. Replacing step flashing at one side of a chimney is a smaller job than replacing flashing on all sides with decking repair, and either grows if the crown or brickwork also needs a mason's attention.

Dated third-party market ranges for flashing work, with sources and conflicts shown, are gathered in the roof replacement cost guide on this site. Those are market figures, not ZT Contracting LLC prices. Because flashing work spans resealing at the low end to full replacement with masonry counter-flashing at the high end, the scope must be read, not assumed.

How a chimney flashing leak is assessed and repaired

Assessment comes first. A roofer inspects the step flashing and counter-flashing, the shingles around the chimney, the decking at the chimney line, and the visible crown and brickwork, to decide whether the source is flashing, the roof surface, or masonry. That decision sets the trade: flashing and roof-surface work belong to the roofer, and crown, brick, and mortar work belong to a mason.

Flashing repair generally means removing the affected flashing, checking and repairing the decking underneath, installing new step flashing woven with the shingles, and setting counter-flashing into the chimney. Sealant alone, applied over failed flashing, covers the symptom while the joint keeps moving. When the crown or brickwork is the source, the roofer's assessment should say so plainly, and the masonry work should go to a mason.

Common mistakes to avoid

The mistakes below are common around chimney leaks, and all of them delay the real repair.

  • Sealing over failed flashing - sealant over a moving joint fails with the next freeze-thaw cycle.
  • Assuming every chimney leak is roofing - crown and brick failures need a mason, and roofing work over a masonry leak wastes the effort.
  • Climbing onto the roof to look - chimney areas concentrate fall hazards and fragile flashing.
  • Waiting for the stain to grow - water at the chimney line reaches framing and interior finishes steadily.

When to call a professional

Call a roofer when stains appear near the chimney, when dampness follows wind-driven rain, or when flashing looks loose or damaged from the ground. An assessment identifies the source and the trade before any work starts. Call ZT Contracting LLC at (515) 385-2566 to arrange a roof inspection in Des Moines.

Frequently Asked Questions

Why is my roof leaking around the chimney in Des Moines IA?

Most often the flashing has failed: freeze-thaw movement, aging sealant, and storm damage open the joint where the chimney meets the roof. The crown and brickwork can also admit water, and that work belongs to a mason.

What decides the scope of chimney flashing repair in Des Moines Iowa?

Which flashing layer failed, how far the water traveled, whether decking needs repair, and whether masonry work is also needed. Dated third-party market ranges are in the cost guide on this site.

Can I fix a chimney leak myself in Des Moines IA?

Assessment and repair belong to a professional: the work involves heights, flashing details, and the roofer-mason line. Homeowner effort belongs on noting stains and timing, and calling for an assessment.

What causes chimney flashing to fail in Des Moines Iowa?

Freeze-thaw movement between the chimney and the roof, aging sealant and fasteners, and wind and hail damage. Step flashing and counter-flashing both protect the joint, and failure in either layer admits water.

Who fixes a chimney leak: a roofer or a mason?

Flashing is the roofer's work, and the crown, brick, and mortar are the mason's. An assessment decides which trade owns the leak before work starts.

Get help with roofing in Des Moines

Chimney leaks sit on the line between two trades, and the first step is knowing which side the leak is on. Call ZT Contracting LLC at (515) 385-2566 to arrange an assessment of a chimney-area leak in Des Moines.

Tagged withchimney leakflashingroof repairdes moineswater damage

A few answers before you start.

Need chimney leak repair in Des Moines? We can help.

Call ZT Contracting LLC at (515) 385-2566 to arrange an inspection of a chimney-area leak. The inspection identifies whether the source is flashing, the roof surface, or masonry that needs a mason.